JLX12864G液晶显示屏驱动
路过羊圈的狼
帮助1人
晶联迅液晶显示屏驱动
型号：JLX12864G-109 Ver2.0
单片机：STM32F103C8T6（72MHz）
开发平台：STM32CubeMX Keil
硬件连接：
LCD_CS --> PB3
LCD_RES --> PB4
LCD_RS --> PB5
LCD_CLK(D6) --> PB6
LCD_SDA(D7) --> PB7
其余电源引脚连接到5V系统电压。
此款液晶屏的驱动芯片实际为ST7565R。
注1：本显示屏为带字库屏，其使用方法为通过一组串口读取屏幕字库芯片的内容，然后再用另外一组串口去写入到屏幕，因为要连接的导线比较多，所以本程序没有去引用它。
注2：本显示屏默认为并口驱动，需要调整PCB上的电阻切换到串口模式。即PCB上原来的R6电阻，调整到R7位置。如下图：
头文件：
#ifndef __JL12864G_109_H
#define __JL12864G_109_H
#include "main.h"
void LCD_Init(void);
void LCD_Clear(void);
void LCD_DispStr8x16(uint8_t _ucPage,uint8_t _ucColumn,char *str);
void LCD_DispNum(uint8_t _ucPage,uint8_t _ucColumn,uint16_t num,uint8_t _ucLenth);
#endif
程序文件，相比官方文件，增加了数字显示：
#include "jxl12864g-109.h"
#include "font.h"
#define LCD_CS_H() HAL_GPIO_WritePin(LCD_CS_GPIO_Port,LCD_CS_Pin,GPIO_PIN_SET)
#define LCD_CS_L() HAL_GPIO_WritePin(LCD_CS_GPIO_Port,LCD_CS_Pin,GPIO_PIN_RESET)
#define LCD_RS_H() HAL_GPIO_WritePin(LCD_RS_GPIO_Port,LCD_RS_Pin,GPIO_PIN_SET)
#define LCD_RS_L() HAL_GPIO_WritePin(LCD_RS_GPIO_Port,LCD_RS_Pin,GPIO_PIN_RESET)
#define LCD_RES_H() HAL_GPIO_WritePin(LCD_RES_GPIO_Port,LCD_RES_Pin,GPIO_PIN_SET)
#define LCD_RES_L() HAL_GPIO_WritePin(LCD_RES_GPIO_Port,LCD_RES_Pin,GPIO_PIN_RESET)
#define LCD_CLK_L() HAL_GPIO_WritePin(LCD_CLK_GPIO_Port,LCD_CLK_Pin,GPIO_PIN_RESET)
#define LCD_CLK_H() HAL_GPIO_WritePin(LCD_CLK_GPIO_Port,LCD_CLK_Pin,GPIO_PIN_SET)
#define LCD_SDA_L() HAL_GPIO_WritePin(LCD_SDA_GPIO_Port,LCD_SDA_Pin,GPIO_PIN_RESET)
#define LCD_SDA_H() HAL_GPIO_WritePin(LCD_SDA_GPIO_Port,LCD_SDA_Pin,GPIO_PIN_SET)
#define LCD_Delayms(x) HAL_Delay(x)
#define REG_DATA 1
#define REG_CMD 0
/****
* 功能：写数据到液晶屏
* 输入：_ucCmd=数据寄存器或者命令寄存器,_ucData=数据
* 输出：无
****/
static void LCD_Write(uint8_t _ucReg,uint8_t _ucData)
{
uint8_t i;
if(_ucReg) LCD_RS_H();
else LCD_RS_L();
for(i=0;i<8;i )
{
LCD_CLK_L();
if(_ucData & 0x80) LCD_SDA_H();
else LCD_SDA_L();
LCD_CLK_H();
_ucData <<= 1;
}
}
/****
* 功能：初始化液晶屏
* 输入：无
* 输出：无
****/
void LCD_Init(void)
{
LCD_CS_L();
LCD_RES_L(); /*低电平复位*/
LCD_Delayms(20);
LCD_RES_H(); /*复位完成*/
LCD_Delayms(20);
LCD_Write(REG_CMD,0XE2); /*软复位*/
LCD_Delayms(5);
LCD_Write(REG_CMD,0x2c); /*升压1*/
LCD_Delayms(5);
LCD_Write(REG_CMD,0x2e); /*升压2*/
LCD_Delayms(5);
LCD_Write(REG_CMD,0x2f); /*升压3*/
LCD_Delayms(5);
LCD_Write(REG_CMD,0x24); /*粗调对比度，0x20-0x27*/
LCD_Write(REG_CMD,0x81); /*微调对比度*/
LCD_Write(REG_CMD,0x1b); /*微调对比度值，0x00-0x3f*/
LCD_Write(REG_CMD,0xa2); /*1/9偏压比*/
LCD_Write(REG_CMD,0xc8); /*行扫描顺序：从上到下*/
LCD_Write(REG_CMD,0xa0); /*列扫描顺序：从左到右*/
LCD_Write(REG_CMD,0x60); /*起始行：第一行开始*/
// LCD_Write(REG_CMD,0xA7); /*反显*/
LCD_Write(REG_CMD,0xaf); /*开显示*/
LCD_CS_H();
}
//
/****
* 功能：设置屏幕的位置
* 输入：无
* 输出：无
****/
static void LCD_SetPos(uint8_t _ucPage,uint8_t _ucColumn)
{
LCD_CS_L();
_ucPage -= 1;
LCD_Write(REG_CMD,0xb0 _ucPage);
LCD_Write(REG_CMD,((_ucColumn>>4) & 0x0f) 0x10);
LCD_Write(REG_CMD,(_ucColumn & 0x0f));
}
/****
* 功能：清屏
* 输入：无
* 输出：无
****/
void LCD_Clear(void)
{
uint8_t i,j;
LCD_CS_L();
for(i=0; i<9; i )
{
LCD_SetPos(1 i,1);
for(j=0; j<132; j )
{
LCD_Write(REG_DATA,0x00);
}
}
LCD_CS_H();
}
/****
* 功能：显示单个8*16字符
* 输入：无
* 输出：无
****/
static void LCD_DispChar8x16(uint8_t _ucPage,uint8_t _ucColumn,uint8_t *p)
{
uint8_t i,j;
LCD_CS_L();
for(j=0; j<2; j )
{
LCD_SetPos(_ucPage j,_ucColumn);
for(i=0; i<8; i )
{
LCD_Write(REG_DATA,*p);
p ;
}
}
LCD_CS_H();
}
//
//m^n函数
//返回值:m^n次方.
uint32_t LCD_Pow(uint8_t m,uint8_t n)
{
uint32_t result=1;
while(n--)result*=m;
return result;
}
/****
* 功能：显示8*16字符串
* 输入：无
* 输出：无
****/
void LCD_DispStr8x16(uint8_t _ucPage,uint8_t _ucColumn,char *str)
{
uint8_t num,i;
uint8_t buff[16];
while(*str != '\0')
{
num = *str - ' ';/*定位字符在二维数组中的位置*/
for(i=0; i<16; i )/*获取字符的取模数据*/
{
buff[i] = ASCII_8X16[num][i];
}
LCD_DispChar8x16(_ucPage,_ucColumn,buff);
_ucColumn = 8;
str ;
}
}
/****
* 功能：显示8*16字符数字
* 输入：
* 输出：无
****/
void LCD_DispNum(uint8_t _ucPage,uint8_t _ucColumn,uint16_t num,uint8_t _ucLenth)
{
uint8_t i,t,temp;
uint8_t enshow=0;
uint8_t buff[16];
for(t=0;t<_ucLenth;t )
{
temp=(num/LCD_Pow(10,_ucLenth-t-1));
if(enshow==0&&t<(_ucLenth-1))
{
if(temp==0)
{
LCD_DispStr8x16(_ucPage,_ucColumn 8*t," ");
continue;
}else enshow=1;
}
temp = 16 ;
for(i=0; i<16; i )/*获取字符的取模数据*/
{
buff[i] = ASCII_8X16[temp][i];
}
LCD_DispChar8x16(_ucPage,_ucColumn 8*t,buff);
}
}
//
使用的是自定义的字库，文件如下，注意取模方式：
#ifndef __FONT_H
#define __FONT_H
#include "main.h"
/**
自定义取模方式：
* 列行式
* 逆向（低位在前）
**/
const uint8_t ASCII_8X16[95][16]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x10,0x0C,0x02,0x10,0x0C,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x40,0xC0,0x78,0x40,0xC0,0x78,0x00,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x00},/*"#",3*/
{0x00,0x70,0x88,0x88,0xFC,0x08,0x30,0x00,0x00,0x18,0x20,0x20,0xFF,0x21,0x1E,0x00},/*"$",4*/
{0xF0,0x08,0xF0,0x80,0x60,0x18,0x00,0x00,0x00,0x31,0x0C,0x03,0x1E,0x21,0x1E,0x00},/*"%",5*/
{0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x2C,0x19,0x27,0x21,0x10},/*"&",6*/
{0x00,0x12,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00},/*"(",8*/
{0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00},/*")",9*/
{0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x0F,0x01,0x01,0x01},/*" ",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x90,0x70,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0xC0,0x38,0x04,0x00,0x00,0x60,0x18,0x07,0x00,0x00,0x00,0x00},/*"/",15*/
{0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00},/*"0",16*/
{0x00,0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00},/*"1",17*/
{0x00,0x70,0x08,0x08,0x08,0x08,0xF0,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00},/*"2",18*/
{0x00,0x30,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x18,0x20,0x21,0x21,0x22,0x1C,0x00},/*"3",19*/
{0x00,0x00,0x80,0x40,0x30,0xF8,0x00,0x00,0x00,0x06,0x05,0x24,0x24,0x3F,0x24,0x24},/*"4",20*/
{0x00,0xF8,0x88,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x20,0x20,0x20,0x11,0x0E,0x00},/*"5",21*/
{0x00,0xE0,0x10,0x88,0x88,0x90,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x20,0x1F,0x00},/*"6",22*/
{0x00,0x18,0x08,0x08,0x88,0x68,0x18,0x00,0x00,0x00,0x00,0x3E,0x01,0x00,0x00,0x00},/*"7",23*/
{0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00},/*"8",24*/
{0x00,0xF0,0x08,0x08,0x08,0x10,0xE0,0x00,0x00,0x01,0x12,0x22,0x22,0x11,0x0F,0x00},/*"9",25*/
{0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00},/*"<",28*/
{0x00,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x00,0x02,0x02,0x02,0x02,0x02,0x02,0x00},/*"=",29*/
{0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00},/*">",30*/
{0x00,0x70,0x48,0x08,0x08,0x88,0x70,0x00,0x00,0x00,0x00,0x30,0x37,0x00,0x00,0x00},/*"?",31*/
{0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x28,0x2F,0x28,0x17,0x00},/*"@",32*/
{0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20},/*"A",33*/
{0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00},/*"B",34*/
{0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00},/*"C",35*/
{0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00},/*"D",36*/
{0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00},/*"E",37*/
{0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00},/*"F",38*/
{0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00},/*"G",39*/
{0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20},/*"H",40*/
{0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"I",41*/
{0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00},/*"J",42*/
{0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00},/*"K",43*/
{0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00},/*"L",44*/
{0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x01,0x3E,0x01,0x3F,0x20,0x00},/*"M",45*/
{0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00},/*"N",46*/
{0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00},/*"O",47*/
{0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00},/*"P",48*/
{0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x28,0x28,0x30,0x50,0x4F,0x00},/*"Q",49*/
{0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20},/*"R",50*/
{0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00},/*"S",51*/
{0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"T",52*/
{0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"U",53*/
{0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00},/*"V",54*/
{0x08,0xF8,0x00,0xF8,0x00,0xF8,0x08,0x00,0x00,0x03,0x3E,0x01,0x3E,0x03,0x00,0x00},/*"W",55*/
{0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20},/*"X",56*/
{0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"Y",57*/
{0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00},/*"Z",58*/
{0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00},/*"[",59*/
{0x00,0x04,0x38,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00},/*"\",60*/
{0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x04,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80},/*"_",63*/
{0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x19,0x24,0x24,0x12,0x3F,0x20,0x00},/*"a",65*/
{0x10,0xF0,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00},/*"b",66*/
{0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00},/*"c",67*/
{0x00,0x00,0x80,0x80,0x80,0x90,0xF0,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20},/*"d",68*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x24,0x24,0x24,0x24,0x17,0x00},/*"e",69*/
{0x00,0x80,0x80,0xE0,0x90,0x90,0x20,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"f",70*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00},/*"g",71*/
{0x10,0xF0,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"h",72*/
{0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00},/*"j",74*/
{0x10,0xF0,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x06,0x29,0x30,0x20,0x00},/*"k",75*/
{0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"l",76*/
{0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F},/*"m",77*/
{0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"n",78*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"o",79*/
{0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0x91,0x20,0x20,0x11,0x0E,0x00},/*"p",80*/
{0x00,0x00,0x00,0x80,0x80,0x00,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0x91,0xFF,0x80},/*"q",81*/
{0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00},/*"r",82*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00},/*"s",83*/
{0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x10,0x00},/*"t",84*/
{0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20},/*"u",85*/
{0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x03,0x0C,0x30,0x0C,0x03,0x00,0x00},/*"v",86*/
{0x80,0x80,0x00,0x80,0x80,0x00,0x80,0x80,0x01,0x0E,0x30,0x0C,0x07,0x38,0x06,0x01},/*"w",87*/
{0x00,0x80,0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x20,0x31,0x0E,0x2E,0x31,0x20,0x00},/*"x",88*/
{0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x81,0x86,0x78,0x18,0x06,0x01,0x00},/*"y",89*/
{0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0xFC,0x02,0x02,0x00,0x00,0x00,0x00,0x01,0x3E,0x40,0x40},/*"{",91*/
{0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00},/*"|",92*/
{0x02,0x02,0xFC,0x00,0x00,0x00,0x00,0x00,0x40,0x40,0x3E,0x01,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x02,0x01,0x02,0x02,0x04,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/
};
#endif
//
最终驱动效果如下：
这篇好文章是转载于：学新通技术网
- 版权申明： 本站部分内容来自互联网，仅供学习及演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，请提供相关证据及您的身份证明，我们将在收到邮件后48小时内删除。
- 本站站名： 学新通技术网
- 本文地址： /boutique/detail/tanhgabckf
系列文章
更多
同类精品
更多
-
photoshop保存的图片太大微信发不了怎么办
PHP中文网 06-15 -
《学习通》视频自动暂停处理方法
HelloWorld317 07-05 -
word里面弄一个表格后上面的标题会跑到下面怎么办
PHP中文网 06-20 -
Android 11 保存文件到外部存储，并分享文件
Luke 10-12 -
photoshop扩展功能面板显示灰色怎么办
PHP中文网 06-14 -
微信公众号没有声音提示怎么办
PHP中文网 03-31 -
excel下划线不显示怎么办
PHP中文网 06-23 -
excel打印预览压线压字怎么办
PHP中文网 06-22 -
TikTok加速器哪个好免费的TK加速器推荐
TK小达人 10-01 -
怎样阻止微信小程序自动打开
PHP中文网 06-13
